TL;DR: Payment Terminal Board for Turkey
About AndroidSBC and the Smart Payment Terminal Android Motherboard Family
AndroidSBC builds smart payment terminal Android motherboards for the unattended and attended ends of the same market. A international market buyer can take a countertop configuration for a shop counter and an outdoor configuration for a charging pillar from one supplier, on one Android baseline, with one SDK. The qualification work happens on the Longgang bench with the actual printer mechanism, reader antenna and scan engine the France integrator intends to buy, and the current draw, the print speed and the decode result are written into the shipment file rather than left for the integrator to discover on site.
WF-SPT-06 Technical Specifications
| Parameter | AndroidSBC WF-SPT-06 (kiosk payment terminal build with large touch panel) | Industry Average |
|---|---|---|
| Processor | RK3399 dual-core ARM Cortex-A72 2.0GHz plus quad-core ARM Cortex-A53 1.5GHz SoC | Older dual-core or quad-core Cortex-A7 SoC |
| Process node | 28nm | Older 40nm process |
| GPU | Mali-T860 MP4 | Older Mali-400 or basic 2D GPU |
| Memory | 4GB LPDDR4 | DDR3 512MB or 1GB on competing boards |
| Storage | 32GB eMMC plus TF card up to 128GB | NAND flash 4GB or 8GB on competing boards |
| Display and touch | 8-inch 1920x1080 eDP capacitive touch panel with 10-point capacitive touch on the main panel | 4.3-inch 480x800 panel with resistive touch |
| Payment and capture | NFC contactless, IC card and QR with PIN pad header | Camera-only QR capture with no scan engine |
| Printer and peripherals | 80mm thermal printer header with 150mm per second output | No printer control header on competing boards |
| Wireless and positioning | dual-band WiFi 802.11 a/b/g/n/ac with Bluetooth 5.0 | Single-band 2.4G WiFi 802.11n with no modem |
| Interfaces | 1 USB Type-C host and OTG, 2 USB host, 1 RS232, 1 HDMI out, 6 GPIO, 1 thermal printer header | One USB port and no RS232 |
| Operating system | Android 12 with AOSP baseline and optional GMS | Android 9 or Android 10 on competing boards |
| Power and reliability | 12V DC input with 5V/3A peripheral rail, watchdog and scheduled power on, -10C to 50C operating ambient | No battery management and no watchdog |
All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-SPT-06 (kiosk payment terminal build with large touch panel) holds the touch panel, the thermal printer, the reader and the scan engine together while running the 72-hour burn-in loop, a configuration that competing single-platform boards rarely document at the top of the temperature window. For France importers sourcing the WF-SPT family, the WF-SPT-06-A variant is the typical configuration for the quick service restaurant self-ordering kiosks use case, in a payment terminal footprint with a sustained weekly capacity of 5000 pcs/wk.
Challenges in Sourcing Smart Payment Terminal Android Motherboards for France Buyers
Attended and unattended payment hardware share a board but not a duty cycle. The international market buyer who specifies a single configuration for both usually ends up over-specifying the counter and under-specifying the kiosk.
Compliance is where a lot of cheap boards fail. The ANFR file has to name the exact modem, the exact printer mechanism and the exact panel that shipped to international market, and it has to be issued by a body the France acquiring partner recognises. The Marseille - Shanghai lane into France is a weekly service for AndroidSBC, and the 193600 board lot for international market is the 8th shipment this quarter carrying the full compliance set rather than a partial file.
Competitive Comparison: WF-SPT-06 vs Competing Smart Payment Terminal Motherboards
The comparison that matters for France buyers is not chip against chip. It is whether the board arrives with a validated peripheral stack, a signed firmware image and a compliance file that names the parts on the pallet - which is where most competing smart payment terminal boards fall short.
- vs consumer tablet boards: the WF-SPT family carries a printer control header, a reader antenna reference design and a scan engine UART mapping, none of which exist on a tablet derivative board.
- vs single-configuration boards: twelve configurations share one peripheral contract, so a international market buyer can move from a countertop lane to an unattended kiosk without re-qualifying the printer or the reader.
- vs boards without a firmware plan: signed images, staged OTA groups with rollback and a published maintenance window come standard, where competing boards ship an image and leave the France integrator to manage it.
- vs re-spun designs: the bill of materials is frozen per production lot for the length of the agreement, so the board that passed qualification in international market is the board that ships in volume.
Global Cashless Payment, Smart Terminal and Self-Service Checkout Market Trends
The kiosk payment terminal build with large touch panel sits in the middle of a market that is growing on formats rather than on unit replacement. Every new unattended format in France is a new terminal, and every new terminal is a board decision for international market buyers.
- Countertop tier: WF-SPT-02 covers contactless, IC card, QR and receipt printing in one board, which is the configuration most staffed lanes standardise on.
- Unattended tier: WF-SPT-03 pairs the modem with the printer header and the watchdog for vending, lockers and kiosks where nobody is there to reboot the terminal.
- Flagship tier: WF-SPT-05 adds the larger memory and storage bundle, the customer-facing screen option and the wider temperature window that outdoor and high-throughput formats require.
Market growth in France does not automatically translate into margin for the integrator. The programmes that pay are the ones where the board arrives qualified, documented and repeatable, which is the gap AndroidSBC is built to close for international market.
WF-SPT-06 Application Scenarios
The WF-SPT-06 kiosk payment terminal build with large touch panel sits inside a twelve-configuration WF-SPT Android motherboard family from AndroidSBC, a Wanlin Manufacturing Group export brand. The WF-SPT-06-A configuration is the typical build for the quick service restaurant self-ordering kiosks use case, with printer current profile, scan engine mapping and staged OTA management bundled.
- Convenience and grocery counters: the WF-SPT-12 takes contactless, IC card and QR at the till and prints the receipt in one pass.
- Restaurant and quick-service counters: the WF-SPT-05 runs order entry, payment and kitchen ticket printing on the same board.
- Unattended vending and lockers: the WF-SPT-03 pairs the modem with the printer header and the watchdog for sites with no staff present.
- EV charging and fuel forecourts: the WF-SPT-09 holds the wide input range and the sunlight readable panel through a full outdoor season.
- Transit gates and event entry: the WF-SPT-05 takes contactless payment and prints the entry ticket without a fixed counter.
- Self-checkout lanes: one board drives the main panel, the scanner and the receipt printer, with the customer screen option where the format needs it.
- Hotel and resort reception: card pre-authorisation, signature capture and folio printing on a board that also runs the restaurant terminal.
- Hospital and clinic payment desks: card, QR and insurance capture on a locked-down build with staged OTA and an audit trail.
- Government and municipal counters: tax, permit and fee payment on a configuration held for the length of the agreement.
Partnership Models for international market Buyers
For international market partners the choice is between stocking the board, integrating the board or branding the board, and each track carries a different level of engineering support.
- Distribution track: the partner buys the WF-SPT board against a published price list, keeps its own stock, and AndroidSBC supplies the printer profile, the scan mapping and the compliance documents with each lot.
- Integration track: the partner takes the board plus firmware customisation, receipt and language localisation and peripheral validation support, with a joint qualification run at the Longgang factory.
- Private-label track: the WF-SPT board ships under the partner brand with customised boot logo, packaging, enclosure and documentation, on a fixed bill of materials held for the length of the agreement.
Whichever track a international market partner chooses, the board is the same board - what changes is the documentation set, the branding and how much of the integration AndroidSBC carries in France.
Frequently Asked Questions
Does the smart payment terminal board family support a kiosk payment terminal build with large touch panel?
Answer: Yes. AndroidSBC builds the kiosk payment terminal build with large touch panel as part of the twelve-configuration WF-SPT family, so the board arrives with its test report, its certificate set and its signed firmware image for France.
Which configurations are available in the WF-SPT family for France buyers?
Answer: The WF-SPT family covers RK3399 and eleven sister configurations, from the value countertop build to the outdoor sunlight readable build, with one Android baseline across the range for France.
Can one smart payment terminal board drive a touch panel, a thermal printer and a scan engine at once?
Answer: Yes. The board runs the panel, the printer header and the scan UART at the same time, which is the configuration international market integrators validate during the joint qualification run at the Longgang factory.
What payment scheme certification support does AndroidSBC provide for France?
Answer: Certification support for France means ANFR conformity documentation, CE marking with ANFR radio interface registration test reports and a firmware signing record, all bundled into the shipment rather than sent after customs clearance in international market.
What is the minimum order quantity and the sample lead time for France?
Answer: The minimum for a customised build is higher than for a stock configuration, but a international market buyer can start with a sample lot, qualify it on the bench, and then move to a production slot without re-qualification.
Is custom ROM, boot logo or pre-installed app development available?
Answer: Yes. AndroidSBC builds the custom image, validates it against the peripheral contract and ships it on the board, which removes the flashing step from the France integration plan.
How are firmware updates delivered to a France device estate after deployment?
Answer: AndroidSBC manages the France estate through staged OTA: signed images, grouped rollout, automatic rollback on failure and a maintenance window agreed with the international market operations team.
What shipping terms does AndroidSBC support for France orders?
Answer: AndroidSBC supports EXW, FOB, CIF and DAP, quotes Port of Marseille as the default port for France, and prepares the customs file before the container closes for international market.
Contact AndroidSBC: Start Your WF-SPT-06 Sourcing Conversation
Every international market programme starts the same way at AndroidSBC: the format, the peripherals, the certification calendar, then a quotation that holds the configuration for the term.
- Email: Androidsbc@163.com
- Export service hotline: +8613261677119
- Website: https://www.androidsbc.com
- Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China
OEM, ODM and private-label tracks are open for France. AndroidSBC supplies the board, the firmware, the documentation and the qualification support, and international market partners own the channel.